PR100 module in DIN rail holder, front three-quarter view

0-5 V to 0-10 V converter, push-button setup

Article number PR100s05

The PR100s05 scales a 0-5 V DC analogue signal up to 0-10 V DC. The output is calibrated with the push buttons: input at 5 V, press the button for 10 V; input at 0 V, press the button for 0 V. Fine adjustment by hand remains possible afterwards. The output is not galvanically isolated: the output minus is internally connected to the supply minus.

Supply 12 and 24 V DC, operating range 11 to 30 V DC
Input 0-5 V DC
Output 0-10 V DC

Price on request

Lead time on request. Not in stock? We will make it.

Request price and lead time WhatsApp Willem

Other version: PR181-X092. The PR181-X092 also converts 0-5 V to 0-10 V, with an output galvanically isolated from input and supply. It is set up on a display, and the rise and fall rate of the output is adjustable as well. Supply 9 to 30 V DC, ambient temperature -25 to 55 °C, non-condensing. Do input and output need to be isolated, or would you rather set it up on a display? Then choose the PR181. Otherwise the PR100 is sufficient.

Orders are placed by email with a purchase order. We supply businesses only.

Specifications

Specifications
Supply	12 and 24 V DC, operating range 11 to 30 V DC
Input	0-5 V DC
Output	0-10 V DC
Isolation	Not isolated: the output minus (terminal 4) is internally connected to the supply minus (terminal 2)
Setup	Three push buttons and a green LED
Ambient temperature	0 to 55 °C
Dimensions	Board 43 x 72 mm
Mounting	DIN rail holder, supplied as standard

Connections

Connections
Terminal	Function
Terminal 1	Supply plus, 12 or 24 V DC
Terminal 2	Supply minus, also common ground for the analogue signals
Terminal 3	0-10 V output plus
Terminal 4	0-10 V output minus, internally connected to terminal 2
Terminal 5	Not used
Terminal 6	0-5 V input plus
Terminal 7	0-5 V input minus, common ground for the input signal

Datasheet (PDF)PDF, 147 kB

Setup

Set up the module when it is first connected and every time you use a different 0-5 V signal.
Connect the 0-5 V source to terminals 6 (plus) and 7 (minus), and the output to terminals 3 and 4.
Apply 12 or 24 V DC to terminals 1 and 2. The green LED lights continuously.
Hold button 3 for four seconds. The LED flashes green: the module is in programming mode.
Set the input to 5 V, the maximum, for an output of 10 V. Hold button 2 for four seconds. The LED flashes quickly for two seconds.
Set the input to 0 V, the minimum, for an output of 0 V. Hold button 1 for four seconds. The LED flashes quickly for two seconds.
Hold button 3 again for four seconds to save. The LED flashes quickly for two seconds and then lights green continuously. The module is ready for use.
To restore the factory settings: disconnect the supply, hold button 2 and reconnect the supply. If the green LED flashes briefly and quickly, the module has been reset.

Application

Scaling a voltage level from 0-5 V to 0-10 V

PR100 series: converters with push-button setup

The converters in the PR100 series are set up with three push buttons and a green LED on the module. Button 3 puts the module in programming mode, button 2 stores the value for the maximum and button 1 the value for the minimum; button 3 saves. The output can then still be fine-tuned by hand. All versions run on 12 and 24 V DC, operating range 11 to 30 V DC, at an ambient temperature of 0 to 55 °C; the board measures 43 x 72 mm and a DIN rail holder is supplied as standard. The output minus is internally connected to the supply minus: the PR100 is not galvanically isolated. To restore the factory settings, disconnect the supply, hold button 2 and reconnect the supply.

Do input and output need to be isolated, or would you rather set it up on a display? Then choose a module from the PR181 series: it is set up on a display, runs on 9 to 30 V DC and has a galvanically isolated output and an adjustable rise and fall rate. Where a PR181 exists for the same conversion, it is listed on the product page under Other version.

More about the PR100 series