W519A test board, 3D view, front three-quarter: ESP32 module with USB-C, four blue relays and green pluggable terminals along both long edges

Test board for functional testing of electronics: analogue outputs, relays, measuring inputs, Modbus, CAN and LIN, via USB or Wi-Fi

Article number W519A

With the W519A you test a board or module from input to output, without separate power supplies, signal sources and multimeters. The board supplies 0-10 V and 0-24 V voltages, 0-20 mA currents and two digital potentiometers, switches four relays and measures analogue inputs, PWM signals, digital inputs and the current and voltage of two loads up to 5 A. RS485 (Modbus), CAN, LIN and a UART connection talk to the product under test. The board is controlled from a computer via USB-C or Wi-Fi, for example with a test script in Python or by an AI agent; this makes a final test repeatable and recorded.

  • Supply 24 V DC; on USB-C power only the control and the measurements work
  • Input 4 analogue inputs 0-30 V (16 bit), switchable to 0/4-20 mA per channel; 6 PWM inputs 5-24 V (frequency and duty, 1 Hz to over 20 kHz); 4 digital inputs 5-24 V with optocoupler
  • Output 2 x 0-10 V and 2 x 0-24 V (12 bit, short-circuit proof); 2 x 0-20 mA active (4-20 mA in software, load up to approx. 750 Ω at 24 V); 2 PWM outputs (5 V or open drain up to 30 V, 2 A)

Price on request

Supplied in series, from 10 units per item. Not in stock? Then we build your series.

One or a few units only as a trial, for a company with a series in sight.

Orders are placed by email with a purchase order. We supply businesses only.

Specifications

Specifications
Supply24 V DC; on USB-C power only the control and the measurements work
Input4 analogue inputs 0-30 V (16 bit), switchable to 0/4-20 mA per channel; 6 PWM inputs 5-24 V (frequency and duty, 1 Hz to over 20 kHz); 4 digital inputs 5-24 V with optocoupler
Output2 x 0-10 V and 2 x 0-24 V (12 bit, short-circuit proof); 2 x 0-20 mA active (4-20 mA in software, load up to approx. 750 Ω at 24 V); 2 PWM outputs (5 V or open drain up to 30 V, 2 A)
Potentiometer2 digital potentiometers, 10 kΩ and 100 kΩ, 256 steps, up to 24 V
Relays4 changeover contacts, 30 V max. (not for mains voltage)
Measuring channels2 channels for current, voltage and power, 0-5 A and 0-36 V, for example the supply of the product under test
CommunicationRS485 (Modbus), CAN and LIN, each with termination via jumper; 3.3 V UART for the product under test
USBUSB-C for control from a computer and software updates
Wi-FiControl via Wi-Fi (ESP32-S3)
Dimensions72 x 222.5 mm (board)
MountingDIN rail carrier profile (CamdenBoss CIME/M); pluggable screw terminals 5.08 mm

Connections

Connections
TerminalFunction
Terminal X124 V DC supply and 0 V
Terminal X20-10 V outputs (AO1, AO2)
Terminal X30-24 V outputs (AO3, AO4)
Terminal X40-20 mA outputs (IO1, IO2)
Terminal X5, X6Potentiometer 10 kΩ and 100 kΩ (A, wiper, B)
Terminal X7PWM outputs (5 V and open drain)
Terminal X8RS485 (A, B, GND)
Terminal X9-X12Relays 1-4 (NO, COM, NC)
Terminal X13Digital inputs 1-4 and COM
Terminal X14Analogue inputs 1-4
Terminal X15, X16PWM inputs 1-6
Terminal X17Measuring channels 1 and 2 (in, out), up to 5 A
Terminal X18CAN (CANH, CANL, GND)
Terminal X19LIN (LIN, GND)

Printable datasheet

Setup

  1. Connect the 24 V supply to X1 and wire the product under test to the terminals the test needs.
  2. Connect the board to the computer via USB-C, or set up the Wi-Fi network.
  3. Start the test script; it sets the outputs, reads the inputs and records the result.

Application

  • Final test of boards and modules in series production
  • Automated testing from a Python script or an AI agent
  • Test set-up in the lab or during firmware development
  • Endurance test with switching on and off and current measurement of the product under test

Not quite right?

A different input, another range, galvanic isolation or your own logo: we adapt the module for your series.

Question about wiring?

You speak directly with the developer. Call or message Willem on +31 6 45 77 55 93.

W519A

Request price and lead time

Enter the quantity per delivery and per year. You will receive price and lead time by email. You then order with a purchase order.

The fastest way

Send the article number, the quantity per delivery and the quantity per year via WhatsApp to +31 6 83 66 55 88. Willem replies on working days.

Request

Fields marked * are required.

You can also send photos or drawings via WhatsApp(opens in a new tab).

Request price